Pinned
3d •
A new way to make the Spirals
Hey guys to make the Spirals in the way you see on the pictures is literally pain in the ass, very slow and hard process, which is not cheep at all too. It is extreemly tricky to make only the inner ring and drill at least 55 wholes with 1mm diameter and then place the spirals there. So the question is how to make it better, faster, cheeper and everyone with a file to purchase them or scale them up and down? After making some research, I foun out that PCBWAY pcbway.com can actually make a copper layer with 15 onces per square foot, which is 500 microns or thickness or 0.5mm. It is 2 times less than what I made, but is more than enough for a decent current to go through. They can insulate the top and bottom sets of the spirals easily, but the other quston was are they able to connect both sets on the outer and inner ring? After chatting with their support, it seems that this is not a problem at all, because a technique called copper EDGING can be applied there. This is great because now the connection to the inner ring won't be mechanical anymore, but homogenous and super smooth. The next challenge, then, is how to leave 2 spirals from one set and 2 from the other set not connected to the inner ring, because they have to be connected directly to the central rod. And to solve this you can see on the images that we can make those 4 spirals end up with 1mm holes, where we can solder later on a copper wire and extend them on top and the bottom of the crystal, where they have to be connected perpendicularly to each other. I just sent a request to a freelancer on Fiverr who can turn this idea into a proper file format, and then we can upload it to PCBway, see the price for it, and check if it's actually doable. If this works, anyone can make the FlashMatrix Circuit super fast, precise, better, and cheaper, I believe.
Pinned
14d •
The Dinamics of a Space Torus
To construct a solid-state device that produces power based on the geometry, we need to understand the principles and laws of motion so well that we can replace the mechanical motion with the motion of the fields themselves to generate EMF. For this, we need to understand the dynamics inside a Space Torus perfectly, because this Torus replicates every time we havea moving body or signal. This succession or replication we call it Space Tori (Plural). In tommorow meeting, we will talk about Centrifugal Force, Momentum, and how acceleration and pressure can lead to higher potential, and how these ideas relate to the prototypes. Have a look at the text and images, so you can be more familiar with the terminology and have a better visual understanding of these ideas. Everything in life is in constant motion, and if we truly understand the dynamics of the space torus, we can unlock unlimited potential in many different ways. A Space Torus is formed by the interaction of Kinetic and Potential energy flows as a response, while any motion is present through space. Generally, there are 3 components: 1. Meridian Plate Circuits (Axial Loops) 2. Concentric Orbits (Equatorial/Tangential Loops) 3. The Central (Primary) Axis (Axis X) Meridian Plate Circuits (Axial Loops) • Definition: In contrast to the equatorial orbits, the loops that travel through the center and around the outside ( pole-to-pole) are called meridian plate circuits. • Shape: While technically spheres, these loops are so deformed by field pressures that they appear as flattened, polarized plates. • Function: In a magnet, millions of these meridian plates are packed together to form the characteristic "apple-shaped" field,. Relationship and Interaction • Focal Points: Because the axial meridian loops are bundled in orderly concentricity, their collective center points form the concentric orbits found on the equatorial plane. • Particle Creation: Discrete quanta of energy, such as electrons, are created at the centers of these circuits.
18d •
If you need a supplier for some of the parts
Just wanted to drop here the company from China that helps us make most of the parts for these prototypes. They made 1.3-meter-wide copper hemispheres 1.5mm thick, and 80cm ones, and 50cm ones . All of them you can see on the images. They also cut for us the copper triangles for the Stela Octangula. They cut a few of the copper discs for the antigravity device. The bearings and the couplers, shafts, copper rods, and other parts come from this supplier in China: https://demark.en.alibaba.com/ They have great communication, reasonable shipping, and very good prices for the parts.
16d •
The conrs activated directly with Slayer circuit
Both the primary and the output coils are around the connes equatorial plane. Both Have 4 windings. Tou can see that the slayer circuit have just one resistor amd one Transistor and I swapped the resistor value to change and smooth the AC pulses starting from 2.7 kOhms like in this video going to 9 kOhms then 20,50,10,220 kOhms then 1mOhm and even 2 mOhms and the circuit was working. At the end I just realized that even the resistor is not nesesary here, because the feedback wire can provide both The Timing of On and Off but also the minimum amperage needed for the Base to operate. The only thing is that if we don't use resistor at all we have to touch the Base and the positive input lead just ones and then the circuit get excited and continue by itself just with one Transistor. I will share another short video in the comments about this .
11d •
Energy-grid Layout
This is a very crudely done layout picture of the "checkerboard" energy-grid, but it will help to get the point. My father has been mapping them independently for over 20 years, along with trees and plant fields, crystals fields and all the conscious fields along that. Better sketches are coming later. The Black lines are downward going energy "walls", they have a big force in them, it feels bad to stand on them for a long period. Each side of the line is ~6m long. The corners point to cardinal points, north-south-west-east. We call them *Earth penetrating lines*. The Red lines are smaller and upward going energy walls they "overlap" the Earth penetrating lines. We call them *Ascending lines*. Each side of the line is 2m long. Also being on these lines for long period can make you restless, not as much as on the penetrating lines tho. Its corners point to half-cardinal points. At each of the energy-grid "arks" there is at the most middle point an beam or pillar of energy we call the *Middlepole*. (Its marked as red dot on the picture.) It shoots up to the northern sky, somewhere up to the "Polaris star". This middlepole feels very sacred and powerful. Same kind of energy pole is also on top of any fire. It can be felt by just watching the fire without any thoughts in mind. Then breathing inside and allowing eyes to travel upwards over the flame/candle. Very uplifting. Then about meter to north from the Middlepole is a *Spring* which "bubbles" almost water-like energy from underground. (Its marked as the blue dot on the picture.) At different times the Spring might shoot the "waters" with high pressure. Forth from it flows 4 small *Streams/Channels* which stop at the *Earth Penetrating walls* and goes down with them, thus dissecting the Ark into 4 sections. Now in each of these 4 sections there are the *Vortexes*. My english is not well enough to portray how the vortexes look like. (They are marked on the picture as the green dots and swirls.) In each section the vortexes are mirroring the opposite vortex.
1-30 of 71
powered by
skool.com/allistar-center-4289
This is the Metafusion community blending Technology with Consciousness, Science with Metaphysics. We connect what seems to be polarity into one idea.
Suggested communities
Powered by